Description
Details
Features:
- Working Pressure: 20 Bar
- Flow capacity: 150ml/min
- Running Time: 1 ∼ 60 seconds
- Working interval setting time: 3 ∼ 999 minute
- Voltage: 220V
- Tank volume: 1.5 L
Important Notes:
Do not reuse or recycle oil – always use fresh oil of the correct grade.
Choose lower ISO VG grades (e.g., 15, 22, 32) for colder environments or lighter operating conditions.
Use higher ISO VG grades (e.g., 46, 68) for warmer climates or heavier loads.
Oils outside this viscosity range (e.g., SAE 30 ≈ ISO VG 100) are not suitable.
Recommended Lubricants for the Pump (ISO VG 15–68)
For proper operation and to prevent damage, use new industrial lubricants within the viscosity range ISO VG 15–68 (measured at 40°C).
Suitable Lubricants:
- ISO VG 15
- ISO VG 22
- ISO VG 32
- ISO VG 46
- ISO VG 68
These grades are defined by the ISO Viscosity Grade (ISO VG) standard.
Compatible Oil Types:
- Hydraulic oils (e.g., ISO VG 32, 46, 68)
- Industrial circulating oils
- Linear guideWays oils (e.g., Shell Tonna S2 M 32, Shell Tonna S2 M 68) for CNC and Milling machine slideways
The ELOP-1.5 series gear pump is a completely automatic control oil pump; the working time ranges from 1 to 60 seconds and the intermittent time ranges from 3 to 999 minutes. High effectiveness, a compact structure that can be utilized with a volumetric oil separator, pressure relief, etc. Gears, guideway rail lubrication, chain, CNC linear bearings, woodworking machinery, textile machinery, elevators, etc. To eliminate the necessity for manual operation, lubricated at locations such as strips, etc., and used with centralized lubrication accessories
Working Principle of the Pump
The pump operates as a pressure-controlled automatic lubrication system:
Interval Timing: The control unit keeps the pump idle for a preset interval (e.g., 10–999 minutes).
Lubrication Phase: When the interval ends, the pump runs for a set time (e.g., 1–60 seconds), delivering oil under pressure to all lubrication points.
Pressure Detection:
A pressure sensor monitors the system pressure during each cycle.
When the required pressure is reached, the system confirms proper lubrication.
If the pressure is not reached within the lubrication time, the system triggers an alarm like ErP or something else indicating a possible blockage or low oil level.
- This means that at the end of the hose, the pump requires some resistance — in this case, a volumetric oil distributor which, once filled, blocks the flow and creates backpressure. The pump detects this backpressure and ends the lubrication cycle.
Automatic Repeat: The cycle repeats continuously to ensure reliable and consistent lubrication.
A simple diagram of the Centralized Lubrication System
Description and SKU catalog numbers of Centralized Lubrication System elements from the diagram
- Oil station unit (used for large systems for lubrication)
- Standard electric pump for Centralized Lubrication System SKU 1191000
- Hand Lubrication Pump for simple Centralized Lubrication System SKU 1192000
- Oil stop plug, end terminal, can be used to terminate any input, end or output terminal. Oil Sealing Plug SKU 1190001 – 1190002
- Stainless steel Spring Tube Protector SKU 1187001 + 1187021
- Oil T-Distributor SKU 1188012 , 1188013
- Oil Pipe Fittings / PA-6 Nut or PA-4 Nut SKU 1185002 or 1185001
- Oil Pipe Fittings / PB-6 Ball Bushing or PB-4 Ball Bushing SKU 1185012 or 1185011
- Oil Nozzle Joint / PD40X – Direct Joint / start from SKU 1189011 (PD404 – Direct Joint mostly used for HGH/HGW15)
- Oil Nozzle Joint / PL40X – Angle Joint / start from SKU 1189001 (PL404 – Angle Joint mostly used for HGH/HGW15)
- Oil Divider Bridge / M10x1 SKU 1195000
- Volumetric Oil Distributor start from SKU 1194001 (on diagram is shown model: VOD-05-Volumetric / 1194005)
- Oil separator block / start from SKU 1193001 (on diagram is shown model: A-06-10-Oil-Separator / 1193003)
- / Oil Resistance Dispenser nozzle fittings (ask for availability)
- / Oil Resistance Dispenser nozzle on side of lubrication point (ask for availability)
- / Oil Resistance Dispenser nozzle on side of lubrication point behind lubrication brush (ask for availability)
- / Oil Resistance Dispenser nozzle (ask for availability)